DRV8833 1.5A 2-Channel H Bridge DC Motor Drive Board Ultra Small Volume Motor Drive Module Input Voltage 3-10V Pack of 6
DRV8833 1.5A 2-Channel H Bridge DC Motor Drive Board Ultra Small Volume Motor Drive Module Input Voltage 3-10V Pack of 6
DRV8833 1.5A 2-Channel H Bridge DC Motor Drive Board Ultra Small Volume Motor Drive Module Input Voltage 3-10V Pack of 6
Product parameters: Size: 18.516mm Input voltage: 3 - 10V Single H bridge output current: 1.5A, can drive 2 DC geared motors. Built-in overcurrent protection, short circuit protection, undervoltage lockout and overtemperature protection. With low power sleep mode. Uses:It can drive DC motors up to 1.5A and 4-wire stepper motors. Instructions for use: ULT low level is sleep mode (need to disconnect the J2 short solder joint behind the module) OUT1, 0UT2 is a 1-way H-bridge, and the corresponding control is IN1, IN2. OUT3, 0UT4 is the second H-bridge, and the corresponding control is IN3, IN4. EEP is the protection output and is not used by default. VCC is a voltage input of 3 to 10V. GND is grounded.
Product Features
- The motor driver can control up to two DC motors at a constant current of 1.0A (4A peak).
- Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - clockwise (CW), counterclockwise (CCW), short pause and stop.
- Built-in over-current protection, short circuit protection, undervoltage shutdown and over temperature protection. In power saving mode.
- The two motor outputs (A and B) can be controlled separately, the speed of each motor is controlled via a PWM input signal with a frequency up to 100 kHz.
- Mains Current: VM = 2.7-10.8V Output Current: Iout = 1.0A (Average) / 4A (Peak)
More Images
DRV8833 1.5A 2-Channel H Bridge DC Motor Drive Board Ultra Small Volume Motor Drive Module Input Voltage 3-10V Pack of 6
DRV8833 1.5A 2-Channel H Bridge DC Motor Drive Board Ultra Small Volume Motor Drive Module Input Voltage 3-10V Pack of 6
Product parameters: Size: 18.516mm Input voltage: 3 - 10V Single H bridge output current: 1.5A, can drive 2 DC geared motors. Built-in overcurrent protection, short circuit protection, undervoltage lockout and overtemperature protection. With low power sleep mode. Uses:It can drive DC motors up to 1.5A and 4-wire stepper motors. Instructions for use: ULT low level is sleep mode (need to disconnect the J2 short solder joint behind the module) OUT1, 0UT2 is a 1-way H-bridge, and the corresponding control is IN1, IN2. OUT3, 0UT4 is the second H-bridge, and the corresponding control is IN3, IN4. EEP is the protection output and is not used by default. VCC is a voltage input of 3 to 10V. GND is grounded.
Product Features
- The motor driver can control up to two DC motors at a constant current of 1.0A (4A peak).
- Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - clockwise (CW), counterclockwise (CCW), short pause and stop.
- Built-in over-current protection, short circuit protection, undervoltage shutdown and over temperature protection. In power saving mode.
- The two motor outputs (A and B) can be controlled separately, the speed of each motor is controlled via a PWM input signal with a frequency up to 100 kHz.
- Mains Current: VM = 2.7-10.8V Output Current: Iout = 1.0A (Average) / 4A (Peak)
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
DRV8833 1.5A 2-Channel H Bridge DC Motor Drive Board Ultra Small Volume Motor Drive Module Input Voltage 3-10V Pack of 6
Product parameters: Size: 18.516mm Input voltage: 3 - 10V Single H bridge output current: 1.5A, can drive 2 DC geared motors. Built-in overcurrent protection, short circuit protection, undervoltage lockout and overtemperature protection. With low power sleep mode. Uses:It can drive DC motors up to 1.5A and 4-wire stepper motors. Instructions for use: ULT low level is sleep mode (need to disconnect the J2 short solder joint behind the module) OUT1, 0UT2 is a 1-way H-bridge, and the corresponding control is IN1, IN2. OUT3, 0UT4 is the second H-bridge, and the corresponding control is IN3, IN4. EEP is the protection output and is not used by default. VCC is a voltage input of 3 to 10V. GND is grounded.
Product Features
- The motor driver can control up to two DC motors at a constant current of 1.0A (4A peak).
- Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - clockwise (CW), counterclockwise (CCW), short pause and stop.
- Built-in over-current protection, short circuit protection, undervoltage shutdown and over temperature protection. In power saving mode.
- The two motor outputs (A and B) can be controlled separately, the speed of each motor is controlled via a PWM input signal with a frequency up to 100 kHz.
- Mains Current: VM = 2.7-10.8V Output Current: Iout = 1.0A (Average) / 4A (Peak)
